Argus-MIB DEFINITIONS ::= BEGIN

	--==========================================================================
	-- ARGUS.MIB Rev B
	--
	-- NOTE: Refer to RFC2578 for the formal definition of the SNMPv2-SMI MIB.
	--
	-- Changes:
	--
	-- November 3, 2008
	--       
	-- The following new definitions were added:
	-- 		Resync 
	-- 		Alarm Trigger
	-- 		Time stamp
	--
	-- Subtyping removed from sequence definitions.
	--==========================================================================

	IMPORTS
		MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, enterprises
			FROM SNMPv2-SMI
		DisplayString
			FROM SNMPv2-TC;

	argus MODULE-IDENTITY
		LAST-UPDATED "200811030000Z"
		ORGANIZATION "Argus Technologies"
		CONTACT-INFO
		  "        Randy Dahlgren

		   Postal: Argus Technologies
				   5700 Sidley Street
				   Vancouver, BC V5J 5E5
				   Canada

			  Tel: 1-604-436-5900
			  Fax: 1-604-436-1233

		   E-mail: rdahlgren@argus.ca"
		DESCRIPTION
		  "This MIB defines the information block(s) available in system controllers 
		   as defined by the following list: 
				- dcPwrSysDevice: the SM-series of controllers"
	::= { enterprises 7309 }
	
	dcpower	    	    	OBJECT IDENTIFIER ::= { argus 4 }
	dcPwrSysDevice			OBJECT IDENTIFIER ::= { dcpower 1 }
	dcPwrSysVariable		OBJECT IDENTIFIER ::= { dcPwrSysDevice 1 }
	dcPwrSysString			OBJECT IDENTIFIER ::= { dcPwrSysDevice 2 }
	dcPwrSysTraps			OBJECT IDENTIFIER ::= { dcPwrSysDevice 3 }    

	dcPwrSysOutputsTbl		OBJECT IDENTIFIER ::= { dcPwrSysDevice 4 }
	dcPwrSysRelayTbl 		OBJECT IDENTIFIER ::= { dcPwrSysOutputsTbl 1 } 
	dcPwrSysAnalogOpTbl		OBJECT IDENTIFIER ::= { dcPwrSysOutputsTbl 2 } 

	dcPwrSysAlrmsTbl		OBJECT IDENTIFIER ::= { dcPwrSysDevice 5 }
	dcPwrSysRectAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 1 } 
	dcPwrSysDigAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 2 } 
	dcPwrSysCurrAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 3 } 
	dcPwrSysVoltAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 4 } 
	dcPwrSysBattAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 5 } 
	dcPwrSysTempAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 6 } 
	dcPwrSysCustomAlrmTbl 	OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 7 } 
	dcPwrSysMiscAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 8 } 
	dcPwrSysCtrlAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 9 } 
	dcPwrSysAdioAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 10 } 
	dcPwrSysConvAlrmTbl		OBJECT IDENTIFIER ::= { dcPwrSysAlrmsTbl 11 } 

	dcPwrSysInputsTbl		OBJECT IDENTIFIER ::= { dcPwrSysDevice 6 }
	dcPwrSysDigIpTbl		OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 1 }
	dcPwrSysCntrlrIpTbl		OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 2 }
	dcPwrSysRectIpTbl		OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 3 }
	dcPwrSysCustomIpTbl		OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 4 }
	dcPwrSysConvIpTbl		OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 5 }
	dcPwrSysTimerIpTbl		OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 6 }
	dcPwrSysCounterIpTbl	OBJECT IDENTIFIER ::= { dcPwrSysInputsTbl 7 }

	dcPwrExternalControls	OBJECT IDENTIFIER ::= { dcPwrSysDevice 8 }
	dcPwrVarbindNameReference	OBJECT IDENTIFIER ::= { dcPwrSysDevice 9 }


	--==========================================================================
	-- Start of variables
	--==========================================================================

	dcPwrSysChargeVolts OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Battery Charge Voltage. The integer value represent a two digit fix decimal (Value = real voltage * 100) in Volt"
	::= { dcPwrSysVariable 1 }

	dcPwrSysDischargeVolts OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Battery Discharge Voltage. The integer value represent a two digit fix decimal (Value = real voltage * 100) in Volt"
	::= { dcPwrSysVariable  2 }

	dcPwrSysChargeAmps OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Battery Charge Current. The integer value represent a two digit fix decimal (Value = real current * 100) in Amp"
	::= { dcPwrSysVariable  3 }

	dcPwrSysDischargeAmps OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Battery Discharge Current. The integer value represent a two digit fix decimal (Value = real current * 100) in Amp"
	::= { dcPwrSysVariable  4 }

	dcPwrSysMajorAlarm OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Major Alarm"
	::= { dcPwrSysVariable  5 }

	dcPwrSysMinorAlarm OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Minor Alarm"
	::= { dcPwrSysVariable  6 }

	--==========================================================================
	-- Start of Strings
	--==========================================================================

	dcPwrSysSiteName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Site Name"
	::= { dcPwrSysString 1 }

	dcPwrSysSiteCity OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Site City"
	::= { dcPwrSysString 2 }

	dcPwrSysSiteRegion OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Site Region"
	::= { dcPwrSysString 3 }

	dcPwrSysSiteCountry OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Site Country"
	::= { dcPwrSysString 4 }

	dcPwrSysContactName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Contact Name"
	::= { dcPwrSysString 5 }

	dcPwrSysPhoneNumber OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Phone Number"
	::= { dcPwrSysString 6 }

	dcPwrSysSiteNumber OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Site Number"
	::= { dcPwrSysString 7 }

	dcPwrSysSystemType OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The type of system being monitored by the agent"
	::= { dcPwrSysString 8 }

	dcPwrSysSystemSerial OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The serial number of the monitored system"
	::= { dcPwrSysString 9 }

	dcPwrSysSystemNumber OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The number of the monitored system"
	::= { dcPwrSysString 10 }

	dcPwrSysSoftwareVersion OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The version of software running on the monitored system"
	::= { dcPwrSysString 11 }

	dcPwrSysSoftwareTimestamp OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The time stamp of the software running on the monitored system"
	::= { dcPwrSysString 12 }

	--==========================================================================
	-- Start of Tables Information
	--==========================================================================
	--=================
	-- Output table
	--=================
	--========================
	-- Relay output	sub table
	--=========================
	dcPwrSysRelayCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of relay variables in system controller relay table"
	::= { dcPwrSysRelayTbl 1 }

	dcPwrSysRelayTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysRelayEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller rectifier relay output variables"
	::= { dcPwrSysRelayTbl 2 }

	dcPwrSysRelayEntry OBJECT-TYPE
		SYNTAX DcPwrSysRelayEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller relay output group"
		INDEX { dcPwrSysRelayIndex }
		::= { dcPwrSysRelayTable 1 }

	DcPwrSysRelayEntry
	::= SEQUENCE {
		dcPwrSysRelayIndex 			INTEGER,
		dcPwrSysRelayName 			DisplayString,
		dcPwrSysRelayIntegerValue 	INTEGER,
		dcPwrSysRelayStringValue 	DisplayString,
		dcPwrSysRelaySeverity		INTEGER
	}

	dcPwrSysRelayIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the relay variable in the power system controller relay output group"
	::= { dcPwrSysRelayEntry 1 }

	dcPwrSysRelayName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the relay variable as reported by the DC power system controller relay output group"
	::= { dcPwrSysRelayEntry 2 }

	dcPwrSysRelayIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the relay variable as reported by the DC power system controller relay output group"
	::= { dcPwrSysRelayEntry 3 }

	dcPwrSysRelayStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the relay variable as reported by the DC power system controller relay output group"
	::= { dcPwrSysRelayEntry 4 }

	dcPwrSysRelaySeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of relay severity level of the extra variable as reported by the DC power system controller relay output group"
	::= { dcPwrSysRelayEntry 5 }

	--========================
	-- Analog output sub table
	--=========================
	dcPwrSysAnalogOpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of analog output variables in system controller analog output table"
	::= { dcPwrSysAnalogOpTbl 1 }

	dcPwrSysAnalogOpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysAnalogOpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller analog output variables"
	::= { dcPwrSysAnalogOpTbl 2 }

	dcPwrSysAnalogOpEntry OBJECT-TYPE
		SYNTAX DcPwrSysAnalogOpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller analog output group"
		INDEX { dcPwrSysAnalogOpIndex }
		::= { dcPwrSysAnalogOpTable 1 }

	DcPwrSysAnalogOpEntry
	::= SEQUENCE {
		dcPwrSysAnalogOpIndex 			INTEGER,
		dcPwrSysAnalogOpName 			DisplayString,
		dcPwrSysAnalogOpIntegerValue 	INTEGER,
		dcPwrSysAnalogOpStringValue 	DisplayString,
		dcPwrSysAnalogOpSeverity 		INTEGER
	}

	dcPwrSysAnalogOpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the analog variable in the power system controller analog output group"
	::= { dcPwrSysAnalogOpEntry 1 }

	dcPwrSysAnalogOpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the analog variable as reported by the DC power system controller analog output group"
	::= { dcPwrSysAnalogOpEntry 2 }

	dcPwrSysAnalogOpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the analog variable as reported by the DC power system controller analog output group"
	::= { dcPwrSysAnalogOpEntry 3 }

	dcPwrSysAnalogOpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the analog variable as reported by the DC power system controller analog output group"
	::= { dcPwrSysAnalogOpEntry 4 }

	dcPwrSysAnalogOpSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of analog severity level of the extra variable as reported by the DC power system controller analog output group"
	::= { dcPwrSysAnalogOpEntry 5 }

	--=================
	-- Alarm table
	--=================
	--============================
	--  Rectifier alarm group
	--============================
	dcPwrSysRectAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of rectifier alarm variables in system controller alarm table"
	::= { dcPwrSysRectAlrmTbl 1 }

	dcPwrSysRectAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysRectAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller rectifier alarm variables"
	::= { dcPwrSysRectAlrmTbl 2 }

	dcPwrSysRectAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysRectAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller rectifier alarm group"
		INDEX { dcPwrSysRectAlrmIndex }
		::= { dcPwrSysRectAlrmTable 1 }

	DcPwrSysRectAlrmEntry
	::= SEQUENCE {
		dcPwrSysRectAlrmIndex 			INTEGER,
		dcPwrSysRectAlrmName 			DisplayString,
		dcPwrSysRectAlrmIntegerValue 	INTEGER,
		dcPwrSysRectAlrmStringValue 	DisplayString,
		dcPwrSysRectAlrmSeverity		INTEGER
	}

	dcPwrSysRectAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table rectifier alarm group"
	::= { dcPwrSysRectAlrmEntry 1 }

	dcPwrSysRectAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller rectifier alarm group"
	::= { dcPwrSysRectAlrmEntry 2 }

	dcPwrSysRectAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller rectifier alarm group"
	::= { dcPwrSysRectAlrmEntry 3 }

	dcPwrSysRectAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller rectifier alarm group"
	::= { dcPwrSysRectAlrmEntry 4 }

	dcPwrSysRectAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller rectifier alarm group"
	::= { dcPwrSysRectAlrmEntry 5 }

	--============================
	--  Digital alarm group
	--============================
	dcPwrSysDigAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of digital alarm variables in system controller alarm table"
	::= { dcPwrSysDigAlrmTbl 1 }

	dcPwrSysDigAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysDigAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller digital alarm variables"
	::= { dcPwrSysDigAlrmTbl 2 }

	dcPwrSysDigAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysDigAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller digital alarm group"
		INDEX { dcPwrSysDigAlrmIndex }
		::= { dcPwrSysDigAlrmTable 1 }

	DcPwrSysDigAlrmEntry
	::= SEQUENCE {
		dcPwrSysDigAlrmIndex 			INTEGER,
		dcPwrSysDigAlrmName 			DisplayString,
		dcPwrSysDigAlrmIntegerValue 	INTEGER,
		dcPwrSysDigAlrmStringValue 		DisplayString,
		dcPwrSysDigAlrmSeverity 		INTEGER
	}

	dcPwrSysDigAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table digital alarm group"
	::= { dcPwrSysDigAlrmEntry 1 }

	dcPwrSysDigAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller digital alarm group"
	::= { dcPwrSysDigAlrmEntry 2 }

	dcPwrSysDigAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller digital alarm group"
	::= { dcPwrSysDigAlrmEntry 3 }

	dcPwrSysDigAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller digital alarm group"
	::= { dcPwrSysDigAlrmEntry 4 }

	dcPwrSysDigAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller digital alarm group"
	::= { dcPwrSysDigAlrmEntry 5 }

	--============================
	--  Current alarm group
	--============================
	dcPwrSysCurrAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of current alarm variables in system controller alarm table"
	::= { dcPwrSysCurrAlrmTbl 1 }

	dcPwrSysCurrAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysCurrAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller current alarm variables"
	::= { dcPwrSysCurrAlrmTbl 2 }

	dcPwrSysCurrAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysCurrAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller current alarm group"
		INDEX { dcPwrSysCurrAlrmIndex }
		::= { dcPwrSysCurrAlrmTable 1 }

	DcPwrSysCurrAlrmEntry
	::= SEQUENCE {
		dcPwrSysCurrAlrmIndex 			INTEGER,
		dcPwrSysCurrAlrmName 			DisplayString,
		dcPwrSysCurrAlrmIntegerValue 	INTEGER,
		dcPwrSysCurrAlrmStringValue 	DisplayString,
		dcPwrSysCurrAlrmSeverity 		INTEGER
	}

	dcPwrSysCurrAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table current alarm group"
	::= { dcPwrSysCurrAlrmEntry 1 }

	dcPwrSysCurrAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller current alarm group"
	::= { dcPwrSysCurrAlrmEntry 2 }

	dcPwrSysCurrAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller current alarm group"
	::= { dcPwrSysCurrAlrmEntry 3 }

	dcPwrSysCurrAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller current alarm group"
	::= { dcPwrSysCurrAlrmEntry 4 }

	dcPwrSysCurrAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller current alarm group"
	::= { dcPwrSysCurrAlrmEntry 5 }

	--============================
	--  Voltage alarm group
	--============================
	dcPwrSysVoltAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of voltage alarm variables in system controller alarm table"
	::= { dcPwrSysVoltAlrmTbl 1 }

	dcPwrSysVoltAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysVoltAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller voltage alarm variables"
	::= { dcPwrSysVoltAlrmTbl 2 }

	dcPwrSysVoltAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysVoltAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller voltage alarm group"
		INDEX { dcPwrSysVoltAlrmIndex }
		::= { dcPwrSysVoltAlrmTable 1 }

	DcPwrSysVoltAlrmEntry
	::= SEQUENCE {
		dcPwrSysVoltAlrmIndex 			INTEGER,
		dcPwrSysVoltAlrmName 			DisplayString,
		dcPwrSysVoltAlrmIntegerValue 	INTEGER,
		dcPwrSysVoltAlrmStringValue 	DisplayString,
		dcPwrSysVoltAlrmSeverity 		INTEGER
	}

	dcPwrSysVoltAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table voltage alarm group"
	::= { dcPwrSysVoltAlrmEntry 1 }

	dcPwrSysVoltAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller voltage alarm group"
	::= { dcPwrSysVoltAlrmEntry 2 }

	dcPwrSysVoltAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller voltage alarm group"
	::= { dcPwrSysVoltAlrmEntry 3 }

	dcPwrSysVoltAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller voltage alarm group"
	::= { dcPwrSysVoltAlrmEntry 4 }

	dcPwrSysVoltAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller voltage alarm group"
	::= { dcPwrSysVoltAlrmEntry 5 }

	--============================
	--  Battery alarm group
	--============================
	dcPwrSysBattAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of battery alarm variables in system controller alarm table"
	::= { dcPwrSysBattAlrmTbl 1 }

	dcPwrSysBattAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysBattAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller battery alarm variables"
	::= { dcPwrSysBattAlrmTbl 2 }

	dcPwrSysBattAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysBattAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller battery alarm group"
		INDEX { dcPwrSysBattAlrmIndex }
		::= { dcPwrSysBattAlrmTable 1 }

	DcPwrSysBattAlrmEntry
	::= SEQUENCE {
		dcPwrSysBattAlrmIndex 			INTEGER,
		dcPwrSysBattAlrmName 			DisplayString,
		dcPwrSysBattAlrmIntegerValue 	INTEGER,
		dcPwrSysBattAlrmStringValue 	DisplayString,
		dcPwrSysBattAlrmSeverity 		INTEGER
	}

	dcPwrSysBattAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table battery alarm group"
	::= { dcPwrSysBattAlrmEntry 1 }

	dcPwrSysBattAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller battery alarm group"
	::= { dcPwrSysBattAlrmEntry 2 }

	dcPwrSysBattAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller battery alarm group"
	::= { dcPwrSysBattAlrmEntry 3 }

	dcPwrSysBattAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller battery alarm group"
	::= { dcPwrSysBattAlrmEntry 4 }

	dcPwrSysBattAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller battery alarm group"
	::= { dcPwrSysBattAlrmEntry 5 }

	--============================
	--  Temperature alarm group
	--============================
	dcPwrSysTempAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of temperature alarm variables in system controller alarm table"
	::= { dcPwrSysTempAlrmTbl 1 }

	dcPwrSysTempAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysTempAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller temperature alarm variables"
	::= { dcPwrSysTempAlrmTbl 2 }

	dcPwrSysTempAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysTempAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller temperature alarm group"
		INDEX { dcPwrSysTempAlrmIndex }
		::= { dcPwrSysTempAlrmTable 1 }

	DcPwrSysTempAlrmEntry
	::= SEQUENCE {
		dcPwrSysTempAlrmIndex 			INTEGER,
		dcPwrSysTempAlrmName 			DisplayString,
		dcPwrSysTempAlrmIntegerValue 	INTEGER,
		dcPwrSysTempAlrmStringValue 	DisplayString,
		dcPwrSysTempAlrmSeverity 		INTEGER
	}

	dcPwrSysTempAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table temperature alarm group"
	::= { dcPwrSysTempAlrmEntry 1 }

	dcPwrSysTempAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller temperature alarm group"
	::= { dcPwrSysTempAlrmEntry 2 }

	dcPwrSysTempAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller temperature alarm group"
	::= { dcPwrSysTempAlrmEntry 3 }

	dcPwrSysTempAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller temperature alarm group"
	::= { dcPwrSysTempAlrmEntry 4 }

	dcPwrSysTempAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller temperature alarm group"
	::= { dcPwrSysTempAlrmEntry 5 }

	--============================
	--  Custom alarm group
	--============================
	dcPwrSysCustomAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of custom alarm variables in system controller alarm table"
	::= { dcPwrSysCustomAlrmTbl 1 }

	dcPwrSysCustomAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysCustomAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller custom alarm variables"
	::= { dcPwrSysCustomAlrmTbl 2 }

	dcPwrSysCustomAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysCustomAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller custom alarm group"
		INDEX { dcPwrSysCustomAlrmIndex }
		::= { dcPwrSysCustomAlrmTable 1 }

	DcPwrSysCustomAlrmEntry
	::= SEQUENCE {
		dcPwrSysCustomAlrmIndex 	 	INTEGER,
		dcPwrSysCustomAlrmName 			DisplayString,
		dcPwrSysCustomAlrmIntegerValue 	INTEGER,
		dcPwrSysCustomAlrmStringValue 	DisplayString,
		dcPwrSysCustomAlrmSeverity 		INTEGER
	}

	dcPwrSysCustomAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table custom alarm group"
	::= { dcPwrSysCustomAlrmEntry 1 }

	dcPwrSysCustomAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller custom alarm group"
	::= { dcPwrSysCustomAlrmEntry 2 }

	dcPwrSysCustomAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller custom alarm group"
	::= { dcPwrSysCustomAlrmEntry 3 }

	dcPwrSysCustomAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller custom alarm group"
	::= { dcPwrSysCustomAlrmEntry 4 }

	dcPwrSysCustomAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller custom alarm group"
	::= { dcPwrSysCustomAlrmEntry 5 }

	--============================
	--  Misc alarm group
	--============================
	dcPwrSysMiscAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of misc alarm variables in system controller alarm table"
	::= { dcPwrSysMiscAlrmTbl 1 }

	dcPwrSysMiscAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysMiscAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller misc alarm variables"
	::= { dcPwrSysMiscAlrmTbl 2 }

	dcPwrSysMiscAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysMiscAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller misc alarm group"
		INDEX { dcPwrSysMiscAlrmIndex }
		::= { dcPwrSysMiscAlrmTable 1 }

	DcPwrSysMiscAlrmEntry
	::= SEQUENCE {
		dcPwrSysMiscAlrmIndex 			INTEGER,
		dcPwrSysMiscAlrmName 			DisplayString,
		dcPwrSysMiscAlrmIntegerValue 	INTEGER,
		dcPwrSysMiscAlrmStringValue 	DisplayString,
		dcPwrSysMiscAlrmSeverity 		INTEGER
	}

	dcPwrSysMiscAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table misc alarm group"
	::= { dcPwrSysMiscAlrmEntry 1 }

	dcPwrSysMiscAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller misc alarm group"
	::= { dcPwrSysMiscAlrmEntry 2 }

	dcPwrSysMiscAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller misc alarm group"
	::= { dcPwrSysMiscAlrmEntry 3 }

	dcPwrSysMiscAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller misc alarm group"
	::= { dcPwrSysMiscAlrmEntry 4 }

	dcPwrSysMiscAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller misc alarm group"
	::= { dcPwrSysMiscAlrmEntry 5 }

	--============================
	--  Control alarm group
	--============================
	dcPwrSysCtrlAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of control alarm variables in system controller alarm table"
	::= { dcPwrSysCtrlAlrmTbl 1 }

	dcPwrSysCtrlAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysCtrlAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller control alarm variables"
	::= { dcPwrSysCtrlAlrmTbl 2 }

	dcPwrSysCtrlAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysCtrlAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller control alarm group"
		INDEX { dcPwrSysCtrlAlrmIndex }
		::= { dcPwrSysCtrlAlrmTable 1 }

	DcPwrSysCtrlAlrmEntry
	::= SEQUENCE {
		dcPwrSysCtrlAlrmIndex 			INTEGER,
		dcPwrSysCtrlAlrmName 			DisplayString,
		dcPwrSysCtrlAlrmIntegerValue 	INTEGER,
		dcPwrSysCtrlAlrmStringValue 	DisplayString,
		dcPwrSysCtrlAlrmSeverity 		INTEGER 
	}

	dcPwrSysCtrlAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table control alarm group"
	::= { dcPwrSysCtrlAlrmEntry 1 }

	dcPwrSysCtrlAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller control alarm group"
	::= { dcPwrSysCtrlAlrmEntry 2 }

	dcPwrSysCtrlAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller control alarm group"
	::= { dcPwrSysCtrlAlrmEntry 3 }

	dcPwrSysCtrlAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller control alarm group"
	::= { dcPwrSysCtrlAlrmEntry 4 }

	dcPwrSysCtrlAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller control alarm group"
	::= { dcPwrSysCtrlAlrmEntry 5 }


	--============================
	--  ADIO alarm group
	--============================

	dcPwrSysAdioAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of control alarm variables in Adio alarm table"
	::= { dcPwrSysAdioAlrmTbl 1 }

	dcPwrSysAdioAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysAdioAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller Adio alarm variables"
	::= { dcPwrSysAdioAlrmTbl 2 }

	dcPwrSysAdioAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysAdioAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller Adio alarm group"
		INDEX { dcPwrSysAdioAlrmIndex }
		::= { dcPwrSysAdioAlrmTable 1 }

	DcPwrSysAdioAlrmEntry
	::= SEQUENCE {
		dcPwrSysAdioAlrmIndex 			INTEGER,
		dcPwrSysAdioAlrmName 			DisplayString,
		dcPwrSysAdioAlrmIntegerValue 	INTEGER,
		dcPwrSysAdioAlrmStringValue 	DisplayString,
		dcPwrSysAdioAlrmSeverity 		INTEGER
	}

	dcPwrSysAdioAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table Adio alarm group"
	::= { dcPwrSysAdioAlrmEntry 1 }

	dcPwrSysAdioAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller Adio alarm group"
	::= { dcPwrSysAdioAlrmEntry 2 }

	dcPwrSysAdioAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller Adio alarm group"
	::= { dcPwrSysAdioAlrmEntry 3 }

	dcPwrSysAdioAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller Adio alarm group"
	::= { dcPwrSysAdioAlrmEntry 4 }

	dcPwrSysAdioAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC Adio system controller control alarm group"
	::= { dcPwrSysAdioAlrmEntry 5 }



                                             
                                               
	--============================
	--  Converter alarm group
	--============================
	dcPwrSysConvAlrmCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of Converter alarm variables in system controller alarm table"
	::= { dcPwrSysConvAlrmTbl 1 }

	dcPwrSysConvAlrmTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysConvAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller Converter alarm variables"
	::= { dcPwrSysConvAlrmTbl 2 }

	dcPwrSysConvAlrmEntry OBJECT-TYPE
		SYNTAX DcPwrSysConvAlrmEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller Converter alarm group"
		INDEX { dcPwrSysConvAlrmIndex }
		::= { dcPwrSysConvAlrmTable 1 }

	DcPwrSysConvAlrmEntry
	::= SEQUENCE {
		dcPwrSysConvAlrmIndex 			INTEGER,
		dcPwrSysConvAlrmName 			DisplayString,
		dcPwrSysConvAlrmIntegerValue 	INTEGER,
		dcPwrSysConvAlrmStringValue 	DisplayString,
		dcPwrSysConvAlrmSeverity		INTEGER
	}

	dcPwrSysConvAlrmIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the alarm variable in the DC power system controller table Converter alarm group"
	::= { dcPwrSysConvAlrmEntry 1 }

	dcPwrSysConvAlrmName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the alarm variable as reported by the DC power system controller Converter alarm group"
	::= { dcPwrSysConvAlrmEntry 2 }

	dcPwrSysConvAlrmIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the alarm variable as reported by the DC power system controller Converter alarm group"
	::= { dcPwrSysConvAlrmEntry 3 }

	dcPwrSysConvAlrmStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the alarm variable as reported by the DC power system controller Converter alarm group"
	::= { dcPwrSysConvAlrmEntry 4 }

	dcPwrSysConvAlrmSeverity OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The integer value of alarm severity level of the extra variable as reported by the DC power system controller Converter alarm group"
	::= { dcPwrSysConvAlrmEntry 5 }

                                               
                                               
                      

	

	--============
	-- Input table
	--============
	--=====================
	-- Digital input group
	--=====================
	dcPwrSysDigIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of digital input variables in system controller digital input table"
	::= { dcPwrSysDigIpTbl 1 }

	dcPwrSysDigIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysDigIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller digital input variables"
	::= { dcPwrSysDigIpTbl 2 }

	dcPwrSysDigIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysDigIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller digital input group"
		INDEX { dcPwrSysDigIpIndex }
		::= { dcPwrSysDigIpTable 1 }

	DcPwrSysDigIpEntry
	::= SEQUENCE {
		dcPwrSysDigIpIndex 			INTEGER,
		dcPwrSysDigIpName 			DisplayString,
		dcPwrSysDigIpIntegerValue 	INTEGER,
		dcPwrSysDigIpStringValue 	DisplayString
	}

	dcPwrSysDigIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the digital input variable in the DC power system controller table digital input group"
	::= { dcPwrSysDigIpEntry 1 }

	dcPwrSysDigIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the digital input variable as reported by the DC power system controller digital input group"
	::= { dcPwrSysDigIpEntry 2 }

	dcPwrSysDigIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the digital input variable as reported by the DC power system controller digital input group"
	::= { dcPwrSysDigIpEntry 3 }

	dcPwrSysDigIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the digital input variable as reported by the DC power system controller digital input group"
	::= { dcPwrSysDigIpEntry 4 }

	--=========================
	-- Controller input group
	--=========================
	dcPwrSysCntrlrIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of controller input variables in system controller controller input table"
	::= { dcPwrSysCntrlrIpTbl 1 }

	dcPwrSysCntrlrIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysCntrlrIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller controller input variables"
	::= { dcPwrSysCntrlrIpTbl 2 }

	dcPwrSysCntrlrIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysCntrlrIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller controller input group"
		INDEX { dcPwrSysCntrlrIpIndex }
		::= { dcPwrSysCntrlrIpTable 1 }

	DcPwrSysCntrlrIpEntry
	::= SEQUENCE {
		dcPwrSysCntrlrIpIndex 			INTEGER,
		dcPwrSysCntrlrIpName 			DisplayString,
		dcPwrSysCntrlrIpIntegerValue 	INTEGER,
		dcPwrSysCntrlrIpStringValue 	DisplayString
	}

	dcPwrSysCntrlrIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the controller input variable in the DC power system controller table controller input group"
	::= { dcPwrSysCntrlrIpEntry 1 }

	dcPwrSysCntrlrIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the controller input variable as reported by the DC power system controller controller input group"
	::= { dcPwrSysCntrlrIpEntry 2 }

	dcPwrSysCntrlrIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the controller input variable as reported by the DC power system controller controller input group"
	::= { dcPwrSysCntrlrIpEntry 3 }

	dcPwrSysCntrlrIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the controller input variable as reported by the DC power system controller controller input group"
	::= { dcPwrSysCntrlrIpEntry 4 }

	--========================
	-- Rectifier input group
	--========================
	dcPwrSysRectIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of rectifier input variables in system controller rectifier input table"
	::= { dcPwrSysRectIpTbl 1 }

	dcPwrSysRectIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysRectIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller rectifier input variables"
	::= { dcPwrSysRectIpTbl 2 }

	dcPwrSysRectIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysRectIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller rectifier input group"
		INDEX { dcPwrSysRectIpIndex }
		::= { dcPwrSysRectIpTable 1 }

	DcPwrSysRectIpEntry
	::= SEQUENCE {
		dcPwrSysRectIpIndex 	  	INTEGER,
		dcPwrSysRectIpName 			DisplayString,
		dcPwrSysRectIpIntegerValue 	INTEGER,
		dcPwrSysRectIpStringValue 	DisplayString
	}

	dcPwrSysRectIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the rectifier input variable in the DC power system controller table rectifier input group"
	::= { dcPwrSysRectIpEntry 1 }

	dcPwrSysRectIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the rectifier input variable as reported by the DC power system controller rectifier input group"
	::= { dcPwrSysRectIpEntry 2 }

	dcPwrSysRectIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the rectifier input variable as reported by the DC power system controller rectifier input group"
	::= { dcPwrSysRectIpEntry 3 }

	dcPwrSysRectIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the rectifier input variable as reported by the DC power system controller rectifier input group"
	::= { dcPwrSysRectIpEntry 4 }

	--======================
	-- Custom input group
	--======================
	dcPwrSysCustomIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of custom input variables in system controller custom input table"
	::= { dcPwrSysCustomIpTbl 1 }

	dcPwrSysCustomIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysCustomIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller digital custom variables"
	::= { dcPwrSysCustomIpTbl 2 }

	dcPwrSysCustomIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysCustomIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller custom input group"
		INDEX { dcPwrSysCustomIpIndex }
		::= { dcPwrSysCustomIpTable 1 }

	DcPwrSysCustomIpEntry
	::= SEQUENCE {
		dcPwrSysCustomIpIndex 			INTEGER,
		dcPwrSysCustomIpName 			DisplayString,
		dcPwrSysgCustomIpIntegerValue 	INTEGER,
		dcPwrSysCustomIpStringValue 	DisplayString
	}

	dcPwrSysCustomIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the custom input variable in the DC power system controller table custom input group"
	::= { dcPwrSysCustomIpEntry 1 }

	dcPwrSysCustomIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the custom input variable as reported by the DC power system controller custom input group"
	::= { dcPwrSysCustomIpEntry 2 }

	dcPwrSysgCustomIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the custom input variable as reported by the DC power system controller custom input group"
	::= { dcPwrSysCustomIpEntry 3 }

	dcPwrSysCustomIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the custom input variable as reported by the DC power system controller custom input group"
	::= { dcPwrSysCustomIpEntry 4 }
                          
                          
                          
	--========================
	-- Converter input group
	--========================
	dcPwrSysConvIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of Converter input variables in system controller Converter input table"
	::= { dcPwrSysConvIpTbl 1 }

	dcPwrSysConvIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysConvIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller Converter input variables"
	::= { dcPwrSysConvIpTbl 2 }

	dcPwrSysConvIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysConvIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller Converter input group"
		INDEX { dcPwrSysConvIpIndex }
		::= { dcPwrSysConvIpTable 1 }

	DcPwrSysConvIpEntry
	::= SEQUENCE {
		dcPwrSysConvIpIndex 	  	INTEGER,
		dcPwrSysConvIpName 			DisplayString,
		dcPwrSysConvIpIntegerValue 	INTEGER,
		dcPwrSysConvIpStringValue 	DisplayString
	}

	dcPwrSysConvIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the Converter input variable in the DC power system controller table Converter input group"
	::= { dcPwrSysConvIpEntry 1 }

	dcPwrSysConvIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the Converter input variable as reported by the DC power system controller Converter input group"
	::= { dcPwrSysConvIpEntry 2 }

	dcPwrSysConvIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the Converter input variable as reported by the DC power system controller Converter input group"
	::= { dcPwrSysConvIpEntry 3 }

	dcPwrSysConvIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the Converter input variable as reported by the DC power system controller Converter input group"
	::= { dcPwrSysConvIpEntry 4 }
                          
	--========================
	-- Timer input group
	--========================
	dcPwrSysTimerIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of Timererter input variables in system controller Timererter input table"
	::= { dcPwrSysTimerIpTbl 1 }

	dcPwrSysTimerIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysTimerIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller Timererter input variables"
	::= { dcPwrSysTimerIpTbl 2 }

	dcPwrSysTimerIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysTimerIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller Timererter input group"
		INDEX { dcPwrSysTimerIpIndex }
		::= { dcPwrSysTimerIpTable 1 }

	DcPwrSysTimerIpEntry
	::= SEQUENCE {
		dcPwrSysTimerIpIndex 	  		INTEGER,
		dcPwrSysTimerIpName 			DisplayString,
		dcPwrSysTimerIpIntegerValue 	INTEGER,
		dcPwrSysTimerIpStringValue 		DisplayString
	}

	dcPwrSysTimerIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the Timererter input variable in the DC power system controller table Timererter input group"
	::= { dcPwrSysTimerIpEntry 1 }

	dcPwrSysTimerIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the Timererter input variable as reported by the DC power system controller Timererter input group"
	::= { dcPwrSysTimerIpEntry 2 }

	dcPwrSysTimerIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the Timererter input variable as reported by the DC power system controller Timererter input group"
	::= { dcPwrSysTimerIpEntry 3 }

	dcPwrSysTimerIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the Timererter input variable as reported by the DC power system controller Timererter input group"
	::= { dcPwrSysTimerIpEntry 4 }
                          

	--========================
	-- Counter input group
	--========================
	dcPwrSysCounterIpCount OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"Number of Countererter input variables in system controller Countererter input table"
	::= { dcPwrSysCounterIpTbl 1 }

	dcPwrSysCounterIpTable OBJECT-TYPE
		SYNTAX SEQUENCE OF DcPwrSysCounterIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"A table of DC power system controller Countererter input variables"
	::= { dcPwrSysCounterIpTbl 2 }

	dcPwrSysCounterIpEntry OBJECT-TYPE
		SYNTAX DcPwrSysCounterIpEntry
		MAX-ACCESS not-accessible
		STATUS current
		DESCRIPTION	"An entry into the DC power system controller Countererter input group"
		INDEX { dcPwrSysCounterIpIndex }
		::= { dcPwrSysCounterIpTable 1 }

	DcPwrSysCounterIpEntry
	::= SEQUENCE {
		dcPwrSysCounterIpIndex 	  		INTEGER,
		dcPwrSysCounterIpName 			DisplayString,
		dcPwrSysCounterIpIntegerValue 	INTEGER,
		dcPwrSysCounterIpStringValue 	DisplayString
	}

	dcPwrSysCounterIpIndex OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The index of the Countererter input variable in the DC power system controller table Countererter input group"
	::= { dcPwrSysCounterIpEntry 1 }

	dcPwrSysCounterIpName OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..30))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The description of the Countererter input variable as reported by the DC power system controller Countererter input group"
	::= { dcPwrSysCounterIpEntry 2 }

	dcPwrSysCounterIpIntegerValue OBJECT-TYPE
		SYNTAX INTEGER (-1000000000..1000000000)
		MAX-ACCESS read-only	
		STATUS current
		DESCRIPTION	"The integer value of the Countererter input variable as reported by the DC power system controller Countererter input group"
	::= { dcPwrSysCounterIpEntry 3 }

	dcPwrSysCounterIpStringValue OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255))
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	"The string value of the Countererter input variable as reported by the DC power system controller Countererter input group"
	::= { dcPwrSysCounterIpEntry 4 }
                                             
                          

 	--==========================================================================
	-- The OBJECT IDENTIFIERs for the traps must be defined in this manner to
	-- satisfy the NetSight MIB compiler; in particular, nodes cannot be defined 
	-- concatenated in a single line, but must be defined explicitly node by node
	-- (hence, the dcPwrSysDevice.dcPwrSysTraps.dcPwrSysTrap definition)
	-- In addition, forward references to extra system variables are needed for 
	-- dcPwrSysTrap by CastleRock SNMPc for event filter and match features.
	--==========================================================================
	dcPwrSysTrap		OBJECT IDENTIFIER ::= { dcPwrSysTraps 0 }

	--==========================================================================
	-- Start of Traps
	--==========================================================================

	dcPwrSysAlarmActiveTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRectAlrmStringValue,
			dcPwrSysRectAlrmIndex,
			dcPwrSysRectAlrmSeverity,
			dcPwrSysSiteName,
			dcPwrSysAlarmTriggerValue
		}
    	STATUS  current
    	DESCRIPTION "A trap issued when one of the alarms on the DC power system controller became active"
	::= { dcPwrSysTrap 1 }

	dcPwrSysAlarmClearedTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRectAlrmStringValue,
			dcPwrSysRectAlrmIndex,
			dcPwrSysRectAlrmSeverity,
			dcPwrSysSiteName,
			dcPwrSysAlarmTriggerValue
		}
    	STATUS  current
    	DESCRIPTION "A trap issued when one of the active alarms on the DC power system controller is cleared"
	::= { dcPwrSysTrap 2 }

	dcPwrSysRelayTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRelayIntegerValue,
			dcPwrSysRelayStringValue,
			dcPwrSysRelayIndex,
			dcPwrSysRelaySeverity,
			dcPwrSysSiteName
		}
    	STATUS  current
    	DESCRIPTION "A trap issued from a change in state in one of the relays on the DC power system controller"
	::= { dcPwrSysTrap 3 }

	dcPwrSysComOKTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysSiteName
		}
		STATUS  current
		DESCRIPTION "A trap to indicate that communications with a DC power system controller has been established."
	::= { dcPwrSysTrap 4 }

	dcPwrSysComErrTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysSiteName
		}
		STATUS  current
		DESCRIPTION "A trap to indicate that communications with a DC power system controller has been lost."
	::= { dcPwrSysTrap 5 }

	dcPwrSysAgentStartupTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysSiteName
		}
		STATUS  current
		DESCRIPTION "A trap to indicate that the agent software has started up."
	::= { dcPwrSysTrap 6 }

	dcPwrSysAgentShutdownTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysSiteName
		}
		STATUS  current
		DESCRIPTION "A trap to indicate that the agent software has shutdown."
	::= { dcPwrSysTrap 7 }

	dcPwrSysMajorAlarmActiveTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRectAlrmStringValue,
			dcPwrSysRectAlrmIndex,
			dcPwrSysRectAlrmSeverity,
			dcPwrSysSiteName
		}
    	STATUS  current
    	DESCRIPTION "A trap issued as a summary of DC power system status.  It is sent when the system goes into in Major Alarm"
	::= { dcPwrSysTrap 8 }

	dcPwrSysMajorAlarmClearedTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRectAlrmStringValue,
			dcPwrSysRectAlrmIndex,
			dcPwrSysRectAlrmSeverity,
			dcPwrSysSiteName
		}
    	STATUS  current
    	DESCRIPTION "A trap issued as a summary of DC power system status.  It is sent when the system comes out of Major Alarm"
	::= { dcPwrSysTrap 9 }
    
	dcPwrSysMinorAlarmActiveTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRectAlrmStringValue,
			dcPwrSysRectAlrmIndex,
			dcPwrSysRectAlrmSeverity,
			dcPwrSysSiteName
		}
    	STATUS  current
    	DESCRIPTION "A trap issued as a summary of DC power system status.  It is sent when the system goes into in Minor Alarm"
	::= { dcPwrSysTrap 10 }

	dcPwrSysMinorAlarmClearedTrap NOTIFICATION-TYPE
		OBJECTS {
			dcPwrSysRectAlrmStringValue,
			dcPwrSysRectAlrmIndex,
			dcPwrSysRectAlrmSeverity,
			dcPwrSysSiteName
		}
    	STATUS  current
    	DESCRIPTION "A trap issued as a summary of DC power system status.  It is sent when the system comes out of Minor Alarm"
	::= { dcPwrSysTrap 11 }
      
      
	--==========================================================================
	-- Start of External Controls
	--==========================================================================

	dcPwrSysResyncAlarms OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-write
		STATUS current
		DESCRIPTION	"Send/Resend all active alarms that were previously sent through SNMP notification."
	::= { dcPwrExternalControls  1 }
      
	--==========================================================================
	-- Alarm Trigger
	--==========================================================================
	dcPwrSysAlarmTriggerValue OBJECT-TYPE
		SYNTAX INTEGER (0..65535)
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	""
	::= { dcPwrVarbindNameReference  1 }

	--==========================================================================
	-- Time stamp
	--==========================================================================
	dcPwrSysTimeStamp OBJECT-TYPE
		SYNTAX DisplayString (SIZE(0..255)) 
		MAX-ACCESS read-only
		STATUS current
		DESCRIPTION	""
	::= { dcPwrVarbindNameReference  2 }
      
END